01 - Start-Up

Written By: Brian Adams (and one other contributor)
  • Comments: 0
  • Favorites: 0
  • Completions: 1

Difficulty

Easy

Steps

11

Time Required

Suggest a time??

Sections

1

Flags

1

Unsatisfactory Images

Unsatisfactory Images

This guide has low-quality images. Pictures need to be either re-edited or re-taken.

Introduction

Follow this guide to startup the PA-1000 CNC Machine

  1. Push the "STOP" button on the control panel to engage the EStop

    • Push the "STOP" button on the control panel to engage the EStop

    • The button will click in if it has not already been pressed.

    • If the last user followed the shutdown SOP it should be pressed already.

    • This steps makes sure we have a control connection to the machine before the motors are engaged.

    Edit

  2. Turn on the control computer and wait for it to boot.

    • Turn on the control computer and wait for it to boot.

    Edit

  3. Double click on the "Router" icon on the desktop to start Mach3

    • Double click on the "Router" icon on the desktop to start Mach3

    Edit

  4. Ensure that the machine bed is fully clear.

    • Ensure that the machine bed is fully clear.

    • The next steps will enable motion of the machine. Be sure that everyone and everything is clear of the machine before moving on.

    Edit

  5. Check that the EStop cord has not been tripped. The lever on the right side of the machine should be pushed toward the back of the machine

    • Check that the EStop cord has not been tripped.

    • The lever on the right side of the machine should be pushed toward the back of the machine

    Edit

  6. Turn the keyswitch on the front panel counter-clockwise to engage the spindle lockout.

    • Turn the keyswitch on the front panel counter-clockwise to engage the spindle lockout.

    • It is a good practice to remove the key from the lock at the point.

    • The power is removed from the spindle controller when the key is removed from the spindle lockout switch, ensuring the spindle cannot be turned on by the controller.

    Edit

  7. Rotate the STOP switch 1/4 turn clockwise.

    • Rotate the STOP switch 1/4 turn clockwise.

    • The switch will pop out slightly when it has been disengaged.

    • Be careful to not over-rotate the switch.

    Edit

  8. Press the green "PWR" button on the control panel.

    • Press the green "PWR" button on the control panel.

    • The light should come on and remain lit.

    • If the green light does not remain lit, the most likely cause is that an EStop remains tripped. (Check STOP switch and EStop cord.)

    • You should hear and audible click as the motors engage.

    Edit

  9. Click the "Reset" button on the Mach3 screen.

    • Click the "Reset" button on the Mach3 screen.

    Edit

  10. The following steps will cause the machine to move. Be sure again that the bed is clear and that all users are clear.

    • The following steps will cause the machine to move. Be sure again that the bed is clear and that all users are clear.

    • Click the REF ALL HOME button.

    • The machine will home itself to the back corner of the machine.

    Edit

  11. When homing is complete, X Y and Z should be green on the Mach3 DROs.

    • When homing is complete, X Y and Z should be green on the Mach3 DROs.

    • If any axis is still red, it hasn't homed, and may not be ready for use.

    • Ask an area manager for help if reattempting REF ALL HOME isn't successful.

    Edit
Finish Line

One other person completed this guide.

Author

with 1 other contributor

Brian Adams

Member since: 02/26/2018

8,892 Reputation

54 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 2

All Time: 245